LotusTalk - The Lotus Cars Community - Reply to Topic
Thread: First time brake pad change: loctite needed? Reply to Thread
Title:
Message:
Trackback:
Send Trackbacks to (Separate multiple URLs with spaces) :
Post Icons
You may choose an icon for your message from the following list:
 

Register Now



In order to be able to post messages on the LotusTalk - The Lotus Cars Community forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in










  Additional Options
Miscellaneous Options

  Topic Review (Newest First)
10-20-2017 03:04 PM
Pengineer91
Quote:
Originally Posted by LostPawn View Post
Do you have the wheel bolts or wheel studs? Just wondering if studs still leave enough room to remove the rotor.
Bolts. Studs would make it impossible to remove the disk without getting the caliper out of the way. While you could still wiggle the inner pad out with the disk in place, there'd be no way to turn the piston back in without removing the disk.
10-20-2017 02:31 PM
Nstymatt
Quote:
Originally Posted by Pengineer91 View Post
Not everyone realizes that you do not need to remove the rear caliber mounting bolts in order to change the pads.

Pull out the pin and spring, then wiggle out the outside pad (push it towards the center of the hub until it clears, then slide it out) . Once the outside pad is removed, remove the small hex bolt holding the disk, then pull off the disk. It might take a tap or two to break any minor rust holding it onto the hub. Once the disk is removed, rummage under the car to find the inside pad, which has just fallen off the caliper. Note that the factory manual does not call for removal of the caliper mounting bolt.

I find this much easier as I don't have to fight with the e-brake cable, it's easier to twist the piston back in if both bolts remain in place, and no lock-tite or critical torques are necessary.
Interesting, thanks! For some reason all of the DIY tutorials suggest removing the caliper mounting bolt, instead of the rotor. But from what you describe it does sound much easier to remove on hex bolt vs. dealing with loctite, e-brake, etc.
10-19-2017 08:58 PM
marcinr
Quote:
Originally Posted by LostPawn View Post
Do you have the wheel bolts or wheel studs? Just wondering if studs still leave enough room to remove the rotor.
I have studs with S111 Ultradiscs, no way to get the pad out without loosening the caliper bolt.

It's just an anecdote, but I forgot loctite once and my caliper bolt backed out, and on its way out, the wiggling damaged the threads in the upright. I discovered this when my caliper locked my rear wheel coming out of T11 at Laguna Seca. The spin was epic.
10-19-2017 08:18 PM
LostPawn
Quote:
Originally Posted by Pengineer91 View Post
Not everyone realizes that you do not need to remove the rear caliber mounting bolts in order to change the pads.

Pull out the pin and spring, then wiggle out the outside pad (push it towards the center of the hub until it clears, then slide it out) . Once the outside pad is removed, remove the small hex bolt holding the disk, then pull off the disk. It might take a tap or two to break any minor rust holding it onto the hub. Once the disk is removed, rummage under the car to find the inside pad, which has just fallen off the caliper. Note that the factory manual does not call for removal of the caliper mounting bolt.

I find this much easier as I don't have to fight with the e-brake cable, it's easier to twist the piston back in if both bolts remain in place, and no lock-tite or critical torques are necessary.
Do you have the wheel bolts or wheel studs? Just wondering if studs still leave enough room to remove the rotor.
10-19-2017 07:53 PM
Glen
Quote:
Originally Posted by Pengineer91 View Post
Not everyone realizes that you do not need to remove the rear caliber mounting bolts in order to change the pads.
Nice tip!

Glen
10-19-2017 06:13 PM
Pengineer91
Quote:
and had some questions about rear caliper 17mm bolt
Not everyone realizes that you do not need to remove the rear caliber mounting bolts in order to change the pads.

Pull out the pin and spring, then wiggle out the outside pad (push it towards the center of the hub until it clears, then slide it out) . Once the outside pad is removed, remove the small hex bolt holding the disk, then pull off the disk. It might take a tap or two to break any minor rust holding it onto the hub. Once the disk is removed, rummage under the car to find the inside pad, which has just fallen off the caliper. Note that the factory manual does not call for removal of the caliper mounting bolt.

I find this much easier as I don't have to fight with the e-brake cable, it's easier to twist the piston back in if both bolts remain in place, and no lock-tite or critical torques are necessary.
10-19-2017 06:10 PM
Lotusxs Whatever you choose to do with loctite/no loctite....Don't use any product that is rated high strength and "requires heat for removal". I had to do a search and destroy mission in my garage last year to throw this stuff out. If you need that type of threadlocker (regardless of color or brand) it should require a trip to the store and a 1 day waiting period so it's intentional.
10-19-2017 03:47 PM
Glen Excerpt from the shop manual for Lotus Elise, Braking:



The color of thread locker is not always a useful method of determining its properties. For example, Loctite 222 is a low-strength thread locker for small fasteners and it is red. (Edit: Henkel recently changed 222’s color to purple. Large stocks of red 222 are still available at retail outlets.)

The shop manual specifies Permabond A130. It is a medium strength thread locker designed for parts that "need to be dismantled for maintenance." Products similar to Permabond A130 include ...

Permatex 24200 - A blue medium strength thread locker. See the data sheet for more info.
Loctite 243 - A blue medium strength thread locker designed for removal. See the data sheet for more info.

Glen
10-19-2017 02:05 PM
3carmonte
Quote:
Originally Posted by Glen View Post
@Nstymatt - The factory shop manual says to use thread locker on re-assembly.

Glen
Just to put my nose in, the red is over-kill but the blue is the "Goldy-lock" for those caliper bolts. The bolts will never loosen up with it but will break free without torch persuasion. Just a drop at the top of the thread length (head end).
10-19-2017 01:27 PM
Glen @Nstymatt - The factory shop manual says to use thread locker on re-assembly.

Glen
10-19-2017 12:33 PM
Nstymatt Darn! Looks like I'll treat myself to some loctite and be safe than sorry. Thanks for the help everyone!
10-19-2017 04:33 AM
countryboyshane I Loctite and paint mark all my suspension bolts. My bolts never move, even after a whole season of racing. I look at Loctite as a little peace of mind.
10-19-2017 03:58 AM
jds62f and just to add to the confusion, I use it every time :-)
10-18-2017 11:13 PM
Gunpilot Have never used it, and that's on the track car the brakes get abused. Never had a problem.
10-18-2017 09:57 PM
Nstymatt
First time brake pad change: loctite needed?

Hey everyone,

I'm about to do change the brake pads for this first time this weekend and had some questions about rear caliper 17mm bolt. Looking at tutorials online, it looks like loctite is applied to the 17mm bolt from factory. Is it necessary to reapply loctite when re-tightening the bolt? Or is ok to just torque the bolt to spec?

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

 
For the best viewing experience please update your browser to Google Chrome